May 20 2011

DealExtreme: Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

Hello Skooter Blog readers, Today I talk about a Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides (3.5″ Front Chassis Bay Embedded SDHC MS/SD/MMC/TF/M2 Card Reader with 4-USB Port) acquired on DealExtreme. This panel can be installed in a bay of 3.5″ (the same as the 3.5 floppy drives″) any computer enclosure and connected to a pair of USB ports, available on most motherboards.

I decided to purchase this Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides, because recently I upgraded my PC, switching to Intel's Sandy Bridge platform. For both, I had to buy a new motherboard, among other items. The motherboards for Sandy Bridge processors use the P67 or H67 chipsets (codinome Cougar Point), Also Intel, which no longer supports floppy drives and, therefore, all motherboards with the new Intel chipset are leaving unsupported drives to 3.5-″. Of course, manufacturers could include a separate controller, the same manner as they do with the USB 3.0, that is not supported by Intel P67/H67, but who still uses floppies these days?

Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB em sua caixa

Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB ports on your chest

So, with the installation of my new motherboard, Gigabyte GA-P67A field-UD7-B3, I had to retire my old floppy drive. I used to read before all the old disks that still functioned and save your content elsewhere. I ended up finding several college papers and even high school, that, despite not having any value, will be saved as a souvenir. Happily, years buy all the separate components and ride my own computers, and so do not get into the hands of those who ride picks everything anyway and pocket all unused parts. If you have ever bought any micro mounted you should know that the cover of the bays of 3.5″ and 5.25″ occupied most likely not have been delivered. What these guys do with so many caps bays different and incompatible offices is a great mystery. The same goes for bolts that were not used, and even those who should have been used, because I've had the displeasure of open micros in the pig “integrator” used a single screw to secure the motherboard, when was the correct use nine. As if that was not enough, we have the disappearance of cables IDE / SATA unused, memory modules and other parts being handled carelessly, processors fitted with a safety seal under the sink, severely reducing the heat dissipation, incorrect use of thermal grease, among other absurdities we see in 90% of micro-mounted computer stores.

Parte traseira da caixa do Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB

Rear Box Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

Now that was clear because I do not trust anyone to ride my micro, you must be wondering what this has to do with the story, some? Explain: to have assembled my own PC, in tampa bay from de 3.5″ was guarded here, and so I could remove the floppy drive and put the lid in place to not leave a hole in the cabinet. But why leave the bay empty and useless if it could be used for something actually useful, as a card reader? All though, from 2009, I got my Card Reader SD / SDHC / MMC / TF Pisen High Speed ​​USB 2.0, a reader built but would still be more practical, some? The GA-P67A-UD7-B3 also has the advantage of offering an abundance of internal connectors: 4 USB 2.0 e but 4 USB 3.0. Of all these, just a couple of USB connectors 2.0 was being used for the front USB ports cabinet, leaving the other free for the two Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides.

Abrindo a caixa do Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB

Opening the box Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

Let's specifications box Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides:

  • Fits perfectly into a slot of 3.5″ his cabinet
  • Transfer files to any PC or MAC
  • Interface USB 2.0 High SPEED
  • Compatible with USB specification 1.1 and 2.0
  • You can look at and edit files directly on memory cards
  • Upload e download fácil
  • LEDs for indicating read and write
  • LED indicators for power
  • Operation of reading and writing cards plug & play and truck to quente (hot swap)
  • Transfer files up to 480 Mbit / s (USB specification)
  • Compatible with most motherboards, that have the internal USB connector standard 9 pins
Conector molex e cabo USB do Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB

MOLEX connector and USB cable Front Panel to stall of 3.5" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

The requirements are:

  • An internal USB port available (actually two, peas cada of plug 9 pins are two doors)
  • IBM compatible PC or Apple Mac
  • Windows 98SE, 2000, XP, View, 7, Linux Core 2.4, Mac OS 8.6 or higher

Supported formats are:

  • SD, Extreme SD, SD-Ultra, SDHC, SD-Pro, SD Ultra II, SD Elite Pro, HS SD, Ultra Speed SD, SD-Ultra-x, HS MIN SD, MMC, MMC1, MMC2, HS-MMC, RS-MMC, MMC 4.0, MMC-Pro, Mini SD*
  • MS, MS (Magic Gate), MS-Pro (Magic Gate), HS-MS-Pro (Magic Gate), Extreme MS Pro, Ultra MS Pro, MS-Duo*, MS-Duo (Magic Gate)*, MS-Pro-Duo (Magic Gate)*, HS MS Pro*, HS-MS-Pro-Duo (Magic Gate)*, MS Select*, MS Pro Duo*, HS MS Pro Duo*, MS ROM HS Magic Gate Pro Duo*, Magic Storage*
  • T-Flash / MicroSD
  • * indicates that adapter required
Frente do Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB

Front Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

Of all supported formats, for me what really matters is the SD, including SDHC, to download photos. I also found it very useful to read directly the microSD, because then I can read the microSD card and the phone's microSD card Dingoo A-320 without needing adapters.

In addition to the card reader, there are four USB ports. Internally, or connector 9 pines do Front Panel for 3.5 bay″ connects to two USB ports on the motherboard (4 pines each, being the ninth pin should be used to avoid wrong connected). The card reader uses USB ports. The second USB port on the motherboard is connected to a USB hub that contains the 4 ports Front Panel for 3.5 bay″. These 4 ports accept connections 480Mps (Hi Speed), 12Mbps (Full Speed) e 1.5 Mbps (Low Speed), with plug and play and can connect up 127 THROUGH devices cascateamento.

Frente do Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB

Front Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

The USB ports can be used only with bus power or external power aid, provided by the source PC via a molex connector. The bus, By specification, must provide a minimum of 500mA current. USB hubs without external power usually limit each 4 100mA doors in order not to overload the bus, but this is not the case Front Panel for 3.5 bay″. It does not limit the current at each port USB, the only limitation being due to bus. Thus, you can connect an external HD 3.5″ (no external power) even without the hub is not using external power, but probably can not connect 4 their, for therefore the motherboard would have to bear some internal USB output 2A, This should not be the case for most of the plates. On the other hand, 4 pendrives (flash drive) could be attached without any problem.

O Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB por dentro

The Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides inside

Using the USB hub with external power via molex should eliminate any current limitation, and thus even 4 enough energy to USAM dispostivos (as already mentioned the 3.5 external hard drives″ without power supply) could be connected without any problem. The only porém is to link the connector MOLEX, my motherboard does not give any sign of life. Connect the power connector with molex plugs makes no LED indication that the motherboard is powered lights (Detached LED, power button light internal motherboard, etc.) and she does not care at all. If the motherboard is On First, and the molex connector is connected then there is no problem, but of course this would not be feasible.

O Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB instalado no gabinete

The Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB ports installed in the cabinet

I do not know why say with certainty that, but it seems that it is a failed project Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides. Apparently he only joins the wires bus power with the power wires of the molex. This causes current to flow freely from the source to the USB bus, and vice versa. Probably there is some protection at source (Seventeam V-Force ST-850Z-AF) or on the motherboard (likely) that prevents it from operating in this situation. Other motherboards sources and may not have this protection and function normally (probably most), which would explain the error in the project, it may even be intentional to save pieces. Who understands electronics can fix this problem by adding diodes in power lines, so that current flows only from the bus to the Frontal Painel and the source for the Frontal Painel, but never the reverse. I even open the Frontal Painel, but I chose not fiddle around, hardly call you up because many devices with high power consumption while these ports. Then simply not connected the molex and let the 4 USB bus powered only by.

O Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB instalado no gabinete

The Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB ports installed in the cabinet

The cable is not the longest, depending on the position of the bay and the position of the USB connector on the motherboard the length may not be enough. In my case, There is a bay of 3.5″ not mole (I never used foi) where the cable would not reach, but in the bay where I installed (o ficava wave drive of disquetes) cable length was sufficient. A set of screws for fixing Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides the office with the product.

O Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB com cartão SDHC e pendrive conectados

The Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB SDHC card and connected pendrive

A performance test of the card reader was done using SiSoftware Sandra and a 8GB SDHC card from Sandisk in Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides. The results are below:

Teste do Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB no SiSoftware Sandra

Test Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB ports on SiSoftware Sandra

SiSoftware Sandra

Benchmark Results
Device Score : 146.6IOPS
Endurance Factor : 33.60
Results Interpretation : Higher scores are better.

Performance vs. Speed
Drive Score : 18.32IOPM/Mbps
Results Interpretation : Higher scores are better.

4kB Files Test
Read Performance : 294.7IOPS / 1.15MB/s
Write Performance : 29.5IOPS / 118kB/s
Delete Performance : 44.7IOPS
File Fragments : 1.0
Combined Score : 201.9IOPS / 807.49kB/s

64kB Files Test
Read Performance : 188.4IOPS / 11.77MB/s
Write Performance : 30.4IOPS / 2MB/s
Delete Performance : 49.9IOPS
File Fragments : 1.0
Combined Score : 133.1IOPS / 8.32MB/s

1MB Files Test
Read Performance : 18.9IOPS / 18.88MB/s
Write Performance : 9.9IOPS / 10MB/s
Delete Performance : 46.7IOPS
File Fragments : 1.0
Combined Score : 15.7IOPS / 15.75MB/s

16MB Files Test
Read Performance : 1.2IOPS / 19.71MB/s
Write Performance : 0.8IOPS / 12.14MB/s
Delete Performance : 39.4IOPS
File Fragments : 1.0
Combined Score : 1.1IOPS / 17MB/s

256MB Files Test
Read Performance : 0.1IOPS / 19.69MB/s
Write Performance : 0.1IOPS / 13.4MB/s
Delete Performance : 6.2IOPS
File Fragments : 3.0
Combined Score : 0.1IOPS / 17.49MB/s

Performance Test Status
Result ID : MultipleCard Reader 8GB (USB)
Platform Compliance : x64
System Timer : 3.32MHz

Endurance Test Status
Operating System Disk Cache Used : On
Use Overlapped I/O : On
Test File Size : 32MB
Block Size : 4kB
File Fragments : 2

Endurance Benchmark Breakdown
Repeated Sector ReWrite : 1.43MB/s
Sequential Sector Write : 2.13MB/s
Random Sector Write : 37kB/s

Drive
Total Size : 7.4GB
Free Space : 5.54GB, 75%
Cluster Size : 32kB

Physical Disk
Manufacturer : Multiple
Model : Card Reader
Version : 1.00
Interface : USB
Removable Drive : Yes
Queueing On : On

Performance Enhancing Tips
Notice 5901 : CD 1x= 150kB/s; Exercise caution when comparing measured versus published CD ratings.
Notice 5008 : To change benchmarks, click Options.
Notice 5004 : Synthetic benchmark. May not tally with ‘real-life’ performance.
Notice 5006 : Only compare the results with ones obtained using the same version!
Notice 5207 : Consider using the File System Benchmark for non-Flash devices.
Notice 5900 : Endurance factor can only be used on the same type of device (SLC or MLC).
Tip 11 : Use the tab to switch between Detailed and Combined charts.
Tip 2 : Double-click tip or press Enter while a tip is selected for more information about the tip.

For comparison, The same test was done using the SDHC card from Sandisk 8GB of built-in card reader in Dell U2410 monitor. It can be observed that results are very similar:

Teste do Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB no SiSoftware Sandra

Test Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB ports on SiSoftware Sandra

SiSoftware Sandra

Benchmark Results
Device Score : 138.8IOPS
Endurance Factor : 36.00
Results Interpretation : Higher scores are better.

Performance vs. Speed
Drive Score : 17.35IOPM/Mbps
Results Interpretation : Higher scores are better.

4kB Files Test
Read Performance : 278.8IOPS / 1MB/s
Write Performance : 30.3IOPS / 121.3kB/s
Delete Performance : 46.9IOPS
File Fragments : 1.0
Combined Score : 191.9IOPS / 767.46kB/s

64kB Files Test
Read Performance : 173.6IOPS / 10.85MB/s
Write Performance : 34.4IOPS / 2.15MB/s
Delete Performance : 53.0IOPS
File Fragments : 1.0
Combined Score : 124.9IOPS / 7.8MB/s

1MB Files Test
Read Performance : 18.8IOPS / 18.81MB/s
Write Performance : 9.8IOPS / 9.76MB/s
Delete Performance : 50.8IOPS
File Fragments : 1.0
Combined Score : 15.6IOPS / 15.64MB/s

16MB Files Test
Read Performance : 1.2IOPS / 19.72MB/s
Write Performance : 0.7IOPS / 11.89MB/s
Delete Performance : 39.3IOPS
File Fragments : 1.0
Combined Score : 1.1IOPS / 17MB/s

256MB Files Test
Read Performance : 0.1IOPS / 19.73MB/s
Write Performance : 0.1IOPS / 13.33MB/s
Delete Performance : 5.6IOPS
File Fragments : 3.0
Combined Score : 0.1IOPS / 17.5MB/s

Performance Test Status
Result ID : Generic Ultra HS-SD/MMC 8GB (USB)
Platform Compliance : x64
System Timer : 3.32MHz

Endurance Test Status
Operating System Disk Cache Used : On
Use Overlapped I/O : On
Test File Size : 32MB
Block Size : 4kB
File Fragments : 2

Endurance Benchmark Breakdown
Repeated Sector ReWrite : 1.32MB/s
Sequential Sector Write : 2MB/s
Random Sector Write : 33kB/s

Drive
Total Size : 7.4GB
Free Space : 5.54GB, 75%
Cluster Size : 32kB

Physical Disk
Manufacturer : Generic
Model : Ultra HS-SD/MMC
Version : 1.82
Interface : USB
Removable Drive : Yes
Queueing On : On

Performance Enhancing Tips
Notice 5901 : CD 1x= 150kB/s; Exercise caution when comparing measured versus published CD ratings.
Notice 5008 : To change benchmarks, click Options.
Notice 5004 : Synthetic benchmark. May not tally with ‘real-life’ performance.
Notice 5006 : Only compare the results with ones obtained using the same version!
Notice 5207 : Consider using the File System Benchmark for non-Flash devices.
Notice 5900 : Endurance factor can only be used on the same type of device (SLC or MLC).
Tip 11 : Use the tab to switch between Detailed and Combined charts.
Tip 2 : Double-click tip or press Enter while a tip is selected for more information about the tip.

With SiSoftware Sandra can also see the identification of the components. Information about the card reader and USB hub are highlighted in blue:

SiSoftware Sandra

General Information
Controller : Intel(R) 6 Series/C200 Series Chipset Family USB Enhanced Host Controller – 1C26

Root Hub
Compound Device : On
Hub Is Bus Powered : On
Power Switching : Gang-switched
Over-current Protection : Global
Number of Ports : 2

Root Hub: USB Port 1
Status : Device Connected
Device Connected to Port : Generic USB Hub
OEM Device Name : Intel Corp. Integrated Rate Matching Hub
Device ID : VEN_8087, DEV_0024, PRT_01
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 1
Transfer Type : Interrupt
Data Packet Size : 64bytes

Root Hub > Generic USB Hub
Compound Device : On
Hub Is Bus Powered : On
Power Switching : Individual
Over-current Protection : Individual
Number of Ports : 8

Root Hub > Generic USB Hub: USB Port 1
Status : No Device Connected

Root Hub > Generic USB Hub: USB Port 2
Status : No Device Connected

Root Hub > Generic USB Hub: USB Port 3
Status : Device Connected
Device Connected to Port : USB Mass Storage Device
OEM Device Name : Alcor Micro Multi Flash Reader
Device Version : 1.00
Device ID : VEN_058F, DEV_6366, PRT_00
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 2
Transfer Type : Bulk
Data Packet Size : 64bytes

Root Hub > Generic USB Hub: USB Port 4
Status : Device Connected
Device Connected to Port : Generic USB Hub
OEM Device Name : TERMINUS TECHNOLOGY INC. USB-2.0 4-Port HUB
Device Version : 1.11
Device ID : VEN_1A40, DEV_0101, PRT_01
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 1
Transfer Type : Interrupt
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub
Compound Device : On
Hub Is Bus Powered : On
Power Switching : Gang-switched
Over-current Protection : Global
Total Power : 100.00mA
Number of Ports : 4

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 1
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 2
Status : Device Connected
Device Connected to Port : USB Mass Storage Device
OEM Device Name : SanDisk Corp. U3 Cruzer 4GB SDCZ36
Device Version : 2.00
Device ID : VEN_0781, DEV_5530, PRT_00
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 2
Transfer Type : Bulk
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 3
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 4
Status : No Device Connected

Root Hub > Generic USB Hub: USB Port 5
Status : Device Connected
Device Connected to Port : Generic USB Hub
OEM Device Name : NEC HighSpeed Hub
Device Version : 1.00
Device ID : VEN_0409, DEV_0058, PRT_01
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 1
Transfer Type : Interrupt
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub
Compound Device : On
Hub Is Bus Powered : On
Power Switching : Individual
Over-current Protection : Individual
Total Power : 100.00mA
Number of Ports : 4

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 1
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 2
Status : Device Connected
Device Connected to Port : USB Data Fax Voice Modem
OEM Device Name : Conexant Systems (Rockwell) 1329h
Device Version : 1.00
Device ID : VEN_0572, DEV_1329, PRT_00
USB Version : 1.10
Speed : Full (12Mbps)
Configuration Settings : 2
Open Pipes : 5
Transfer Type : Interrupt
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 3
Status : Device Connected
Device Connected to Port : Generic Bluetooth Radio
OEM Device Name : Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Device Version : 31.64
Device ID : VEN_0A12, DEV_0001, PRT_01
USB Version : 2.00
Speed : Full (12Mbps)
Configuration Settings : 1
Open Pipes : 5
Transfer Type : Interrupt
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 4
Status : Device Connected
Device Connected to Port : USB Mass Storage Device
OEM Device Name : SanDisk Corp. U3 Cruzer 4GB SDCZ36
Device Version : 2.00
Device ID : VEN_0781, DEV_5530, PRT_00
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 2
Transfer Type : Bulk
Data Packet Size : 64bytes

Root Hub > Generic USB Hub: USB Port 6
Status : Device Connected
Device Connected to Port : American Power Conversion USB UPS
OEM Device Name : American Power Conversion Back-UPS Pro 500/1000/1500
Device Version : 1.06
Device ID : VEN_051D, DEV_0002, PRT_00
USB Version : 1.10
Speed : Low (1.5Mbps)
Configuration Settings : 1
Open Pipes : 1
Transfer Type : Interrupt
Data Packet Size : 8bytes

Root Hub > Generic USB Hub: USB Port 7
Status : Device Connected
Device Connected to Port : Generic USB Hub
OEM Device Name : 8457 3431h
Device Version : 2.75
Device ID : VEN_2109, DEV_3431, PRT_01
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 1
Transfer Type : Interrupt
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub
Compound Device : On
Hub Is Bus Powered : On
Power Switching : Individual
Over-current Protection : Individual
Total Power : 100.00mA
Number of Ports : 4

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 1
Status : Device Connected
Device Connected to Port : USB Composite Device
OEM Device Name : Microsoft Corp LifeCam VX-3000.
Device Version : 1.01
Device ID : VEN_045E, DEV_00F5, PRT_00
USB Version : 1.10
Speed : Full (12Mbps)
Configuration Settings : 1
Open Pipes : 3
Transfer Type : Isochronous
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 2
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 3
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 4
Status : No Device Connected

Root Hub > Generic USB Hub: USB Port 8
Status : Device Connected
Device Connected to Port : Generic USB Hub
OEM Device Name : 8457 3431h
Device Version : 2.75
Device ID : VEN_2109, DEV_3431, PRT_01
USB Version : 2.00
Speed : High (480Mbps)
Configuration Settings : 1
Open Pipes : 1
Transfer Type : Interrupt
Data Packet Size : 64bytes

Root Hub > Generic USB Hub > Generic USB Hub
Compound Device : On
Hub Is Bus Powered : On
Power Switching : Individual
Over-current Protection : Individual
Total Power : 100.00mA
Number of Ports : 4

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 1
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 2
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 3
Status : No Device Connected

Root Hub > Generic USB Hub > Generic USB Hub: USB Port 4
Status : No Device Connected

Root Hub: USB Port 2
Status : No Device Connected

From the information provided by SiSoftware Sandra, we see that the card reader is described as “Alcor Micro Multi Flash Reader” (058F:6366) and the hub is identified as “Terminus Technology Inc. USB2.0 4-Port HUB” (1A40:0101). Na Door 2 do Hub, which is actually the third door panel, see a Sandisk pendrive connected at high speed (480Mbps).

For only $10,90 USD (U.S. dollars two), I can conclude that the purchase of Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides was a good buy. The photos in this article were discharged with card reader. Eventually also congestion on the two front USB ports of my office. Ali I used to connect my pendrive and remove it when needed would unload some photo, because Card Reader SD / SDHC / MMC / TF Pisen High Speed ​​USB 2.0 it is “chubby” and just blocking USB porta ao dela side (who designed the cabinet left both doors close). With the Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides this problem was solved. As 4 USB ports are well spaced, and the very Card Reader SD / SDHC / MMC / TF Pisen High Speed ​​USB 2.0 is no longer necessary, thanks to the card reader panel.

Pacote da DealExtreme com o Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB

DealExtreme package with Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

As a buy, was made on 07/03/2011 and posted on 09/03. Arrived the day 05/05, Almost two months later. As (not) say or ex-president, never before in the history of this country the Post Office and IRS were so inefficient that time of year (Congratulations PT!). The description of the package came as "CARD READER", with the declared weight 220 programs and declared value of $10,90 USD, real value of the product. The package was not taxed.

Pacote da DealExtreme com o Painel Frontal para baia de 3.5" com leitor de cartões SDHC/MS/SD/MMC/TF/M2 e 4 portas USB

DealExtreme package with Front Panel for 3.5 bay" with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides

And I'm ending here the article on Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides. If you also want to shop in DealExtreme, directly from Hong Kong, click here and good shopping.

Permanent link to this article: https://www.skooterblog.com/2011/05/20/dealextreme-painel-frontal-para-baia-de-3-5-com-leitor-de-cartoes-sdhcmssdmmctfm2-e-4-portas-usb/

Leave a comment

3 Comments on "DealExtreme: Front Panel for 3.5 bay″ with card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides"

Notify about
Avatar
Sort by:   more new | older | top rated
Bruno
Visitor
Bruno

Congratulations for review, perfect

Trackback

[…] May I had bought a front panel bay for 3.5 "card reader and SDHC/MS/SD/MMC/TF/M2 4 USB slides, that substituiu meu drive disquetes of 3.5″, since my current motherboard (Gigabyte […]

Trackback

[…] […]

wpDiscuz