Initiation » [Review] Hub USB 3.0 Orico WH4P1 com 4 doors and entrance to source – AliExpress

April 02 2020

[Review] Hub USB 3.0 Orico WH4P1 com 4 doors and entrance to source – AliExpress

The Hub USB 3.0 Orico WH4P1 com 4 doors and entrance to source was acquired on AliExpress, shop Orico Official Store, for use with my laptop, at Dell Latitude 7370, which has only two USB ports.

Motivation

As mentioned já, I have a work laptop Dell Latitude 7370. It is very light and compact, and it is my choice for travel, but it is very economical in terms of USB ports: there are just two USB Type A ports and another USB Type C port.

One of these ports is constantly used by the receiver wireless mouse, which is a Mouse Logitech MX Anywhere 2. I could even configure it via Bluetooth to save one port, but it's always something I leave it for later. Even because there is no place on the mouse itself to store the receiver and not lose it, as it exists in other models.

In the USB port that is left over eventually I connect pendrives, External HD, cellular, reader, etc. Eventually I need to use one of these and the External HD is already being used by some application. That's where a Hub USB It is necessary to.

I then went in search of a compact USB Hub, that didn't add too much weight to my backpack. Four doors are usually the standard and that's enough for me. External power supply was not a requirement, it would be extra weight to load and I should not connect more than one External HD at the same time. USB 3.0, on the other hand, is a requirement to be able to take full advantage of external USB HDDs and SSDs 3.0.

Choice of Hub USB 3.0 Orico WH4P1

The choice of the Orico brand was due to my previous experience with the brand. I already have two other branded USB hubs, and I've already reviewed them here on the Skooter Blog. Check out:

The W8PH4-U3 is permanently connected on my Mini PC, the MSI Cubes 2, which also has fewer ports than I need. There are four in total, being a Type C, and only two on the back.

The A3H13P2 is permanently connected to my PC, facilitating the connection of external HD, tablet, headphones, cellular, etc. without having to appeal to the doors behind the case.

How both are fulfilling their role well, the choice for Orico again was natural. The brand has a model for all tastes. The WH4P1 is one of the simplest and most compact. It's USB 3.0, has 4 doors and even has an interesting extra: a microUSB port to which an external source not included can be connected. The idea is to connect a cell phone charger or something if necessary. Closed with him.

There were two color options: black and white, and two wire length options: 30cm and 1 metro. As I was looking for something light and compact, I had the option of 30 cm. And I chose black because I prefer my electronics in that color.

Unboxing

The package arrived in 20 calendar days. The Hub USB 3.0 Orico WH4P1 arrived in a bubble envelope. Inside the product was packed in its box.

On one side of the product we have the LED that indicates when it is on, 3 USB slides 3.0 and the microUSB port for power input.

Another USB port 3.0 is isolated on one of the smaller sides. The cable connecting to the laptop goes out the other side.

At the top we have the Orico logo, and at the bottom we have some specifications: the WH4P1 model, 5V and 0.5A input, e a interface.

Check out the photos and video of the unboxing and tests Hub USB 3.0 Orico WH4P1:

Tests

To test Hub USB 3.0 Orico WH4P1 I connected one External HD and two more flash drives, and he identified them all correctly, opening the corresponding folders.

I didn't get to test the external power, it is not something I intend to use. But I hope that or Hub USB 3.0 Orico WH4P1 do not allow current from the external source to flow to the laptop outlet. I've seen this happen with those panels with USB ports for desktop, that allowed the extra supply current (via Molex) flow into the header Motherboard USB, activating a protection of the same that did not allow it to turn on. This is not something I can easily test, then it remains to trust Orico.

In a test with Sisoftware Sandra, these were the information obtained from the Hub USB 3.0 Orico WH4P1:

Root Hub > Generic SuperSpeed USB Hub > Generic SuperSpeed USB Hub > Generic SuperSpeed USB Hub: USB Port #2
Status : Device Connected
Manufacturer : GenesysLogic
Device Connected : USB3.1 Hub
Device ID : VEN_05E3, DEV_0626, PRT_03
Device Version : 6.54
USB Version : 3.10
Speed : Super (4.8Gbps)
Configuration Settings : 1
Open Pipes : 1
Transfer Type : Interrupt
Data Packet Size : 9bytes

Root Hub > Generic SuperSpeed USB Hub > Generic SuperSpeed USB Hub > Generic SuperSpeed USB Hub > Generic SuperSpeed USB Hub
Compound Device : No
Hub Is Bus Powered : No
Power Switching : Gang-switched
Over-current Protection : Global
Total Power : 144.00mA
No. Ports : 4

And with the USB Device Tree Viewer, the information obtained was these:

    =========================== USB Port4 ===========================

Connection Status        : 0x01 (Device is connected)
Port Chain               : 2-18-2-3-4
Properties               : 0x01
 IsUserConnectable       : yes
 PortIsDebugCapable      : no
 PortHasMultiCompanions  : no
 PortConnectorIsTypeC    : no
ConnectionIndex          : 4
CompanionIndex           : 0
 CompanionHubSymLnk      : USB#VID_2109&PID_2813#7&23a116a&0&3#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
 CompanionPortNumber     : 4

      ========================== USB Hub =========================

        ------------------- USB Hub Descriptor -----------------
bDescriptorLength        : 0x09 (9 bytes)
bDescriptorType          : 0x29 (Hub Descriptor)
bNumberOfPorts           : 0x04 (4 Ports)
wHubCharacteristics      : 0x0000
 Power switching         : Ganged
 Compound device         : No
 Over-current protection : Global
 TT Think Time           : At most 8 FS bit times
 Port Indicators         : Not supported
bPowerOnToPowerGood      : 0x00 (0 ms)
bHubControlCurrent       : 0x90 (144 mA)
DeviceRemovable          : 0x00
 Bit 0                   : 0 (reserved, any value)
 Bit 1                   : 0 (Device at Port 1 is removable)
 Bit 2                   : 0 (Device at Port 2 is removable)
 Bit 3                   : 0 (Device at Port 3 is removable)
 Bit 4                   : 0 (Device at Port 4 is removable)
 Bit 5                   : 0 (unused, must be 0)
 Bit 6                   : 0 (unused, must be 0)
 Bit 7                   : 0 (unused, must be 0)
Data (HexDump)           : 09 29 04 00 00 00 90 00 FF                        .).......
HubIsBusPowered          : 0x00 (Self Powered)

        -------------- Extended USB Hub Descriptor -------------
HubType                  : USB 3.0 Hub
HighestPortNumber        : 4

        ---------------- USB 3.0 Hub Descriptor ---------------
bLength                  : 0x0C (12 bytes)
bDescriptorType          : 0x2A
bNumberOfPorts           : 0x04 (4 Ports)
wHubCharacteristics      : 0x0000
 Power switching         : Ganged
 Compound device         : No
 Over-current protection : Global
 TT Think Time           : At most 8 FS bit times
 Port Indicators         : Not supported
bPowerOnToPowerGood      : 0x00
bHubControlCurrent       : 0x90 (576 mA)
bHubHdrDecLat            : 0x02 (0.4 ĩS)
wHubDelay                : 0x15E (350 ns)
DeviceRemovable          : 0x00
 Bit 0                   : 0 (reserved, any value)
 Bit 1                   : 0 (Device at Port 1 is removable)
 Bit 2                   : 0 (Device at Port 2 is removable)
 Bit 3                   : 0 (Device at Port 3 is removable)
 Bit 4                   : 0 (Device at Port 4 is removable)
 Bit 5                   : 0 (unused, must be 0)
 Bit 6                   : 0 (unused, must be 0)
 Bit 7                   : 0 (unused, must be 0)

        ----------------- USB Hub Capabilities ----------------
HighSpeedCapable         : No
HighSpeed                : No
MultiTtCapable           : No
HubIsMultiTt             : No
ArmedWakeOnConnect       : No
IsBusPowered             : No
IsRoot                   : No
Data (HexDump)           : 00 00 00 00                                       ....

        +++++++++++++++++ Device Information ++++++++++++++++++
Device Description       : Generic SuperSpeed USB Hub
Device Path              : \\?\usb#vid_05e3&pid_0626#8&155c2249&0&4#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
Device ID                : USB  VID_05E3&PID_06268&155C2249&0&4
Hardware IDs             : USB  VID_05E3&PID_0626&REV_0654 USBVID_05E3&PID_0626
Driver KeyName           : {36fc9e60-c465-11cf-8056-444553540000}\0043 (GUID_DEVCLASS_USB)
Driver                   : \SystemRootSystem32driversUsbHub3.sys (Version: 10.0.18362.1  Date: 2019-03-19)
Driver Inf               : C:\WINDOWS\inf\usbhub3.inf
Legacy BusType           : PNPBus
Class                    : USB
Class GUID               : {36fc9e60-c465-11cf-8056-444553540000} (GUID_DEVCLASS_USB)
Interface GUID           : {f18a0e88-c30c-11d0-8815-00a0c906bed8} (GUID_DEVINTERFACE_USB_HUB)
Service                  : USBHUB3
Enumerator               : USB
Location Info            : Port_#0004.Hub_#0012
Location IDs             : PCIROOT(0)#PCI(1400)#USBROOT(0)#USB(18)#USB(2)#USB(3)#USB(4), ACPI(_SB_)#ACPI(PCI0)#ACPI(XHC_)#ACPI(RHUB)#ACPI(SSP3)#USB(2)#USB(3)#USB(4)
Container ID             : {9f4b56f0-1df6-11e0-ac64-0800200c9a66}
Manufacturer Info        : (Standard USB HUBs)
Capabilities             : 0x84 (Removable, SurpriseRemovalOK)
Status                   : 0x0180600A (DN_DRIVER_LOADED, DN_STARTED, DN_DISABLEABLE, DN_REMOVABLE, DN_NT_ENUMERATOR, DN_NT_DRIVER)
Problem Code             : 0
Address                  : 4
HcDisableSelectiveSuspend: 0
EnableSelectiveSuspend   : 0
SelectiveSuspendEnabled  : 0
EnhancedPowerMgmtEnabled : 0
IdleInWorkingState       : 1
WakeFromSleepState       : 0
Power State              : D0 (supported: D0, D1, D2, D3, wake from D0, wake from D1, wake from D2)

        +++++++++++++++++ Registry USB Flags +++++++++++++++++
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\usbflags\05E306260654
 osvc                    : REG_BINARY 00 00
 NewInterfaceUsage       : REG_DWORD 00000000 (0)

        ---------------- Connection Information ---------------
Connection Index         : 0x04 (4)
Connection Status        : 0x01 (DeviceConnected)
Current Config Value     : 0x01
Device Address           : 0x20 (32)
Is Hub                   : 0x01 (yes)
Device Bus Speed         : 0x02 (High-Speed) -> not true, see below in Connection Information V2
Number Of Open Pipes     : 0x01 (1 pipe to data endpoints)
Pipe[0]                  : EndpointID=1  Direction=IN   ScheduleOffset=0  Type=Interrupt
Data (HexDump)           : 04 00 00 00 12 01 10 03 09 00 03 09 E3 05 26 06   ..............&.
                           54 06 01 02 00 01 01 02 01 20 00 01 00 00 00 01   T........ ......
                           00 00 00 07 05 81 13 02 00 08 00 00 00 00         ..............

        --------------- Connection Information V2 -------------
Connection Index         : 0x04 (4)
Length                   : 0x10 (16 bytes)
SupportedUsbProtocols    : 0x04
 Usb110                  : 0 (on the)
 Usb200                  : 0 (on the)
 Usb300                  : 1 (yes)
 ReservedMBZ             : 0x00
Flags                    : 0x03
 DevIsOpAtSsOrHigher     : 1 (Is operating at SuperSpeed or higher)
 DevIsSsCapOrHigher      : 1 (Is SuperSpeed capable or higher)
 DevIsOpAtSsPlusOrHigher : 0 (Is not operating at SuperSpeedPlus or higher)
 DevIsSsPlusCapOrHigher  : 0 (Is not SuperSpeedPlus capable or higher)
 ReservedMBZ             : 0x00
Data (HexDump)           : 04 00 00 00 10 00 00 00 04 00 00 00 03 00 00 00   ................

    ---------------------- Device Descriptor ----------------------
bLength                  : 0x12 (18 bytes)
bDescriptorType          : 0x01 (Device Descriptor)
bcdUSB                   : 0x310 (USB Version 3.10)
bDeviceClass             : 0x09 (Hub)
bDeviceSubClass          : 0x00
bDeviceProtocol          : 0x03 (SuperSpeed hub)
bMaxPacketSize0          : 0x09 (9 bytes)
idVendor                 : 0x05E3 (Genesys Logic, Inc.)
idProduct                : 0x0626
bcdDevice                : 0x0654
iManufacturer            : 0x01 (String Descriptor 1)
 *!*ERROR  String descriptor not found
iProduct                 : 0x02 (String Descriptor 2)
 *!*ERROR  String descriptor not found
iSerialNumber            : 0x00 (No String Descriptor)
bNumConfigurations       : 0x01 (1 Configuration)
Data (HexDump)           : 12 01 10 03 09 00 03 09 E3 05 26 06 54 06 01 02   ..........&.T...
                           00 01                                             ..

    ------------------ Configuration Descriptor -------------------
bLength                  : 0x09 (9 bytes)
bDescriptorType          : 0x02 (Configuration Descriptor)
wTotalLength             : 0x001F (31 bytes)
bNumInterfaces           : 0x01 (1 Interface)
bConfigurationValue      : 0x01 (Configuration 1)
iConfiguration           : 0x00 (No String Descriptor)
bmAttributes             : 0xE0
 D7: Reserved, set 1     : 0x01
 D6: Self Powered        : 0x01 (yes)
 D5: Remote Wakeup       : 0x01 (yes)
 D4..0: Reserved, set 0  : 0x00
MaxPower                 : 0x00 (0 mA)
Data (HexDump)           : 09 02 1F 00 01 01 00 E0 00 09 04 00 00 01 09 00   ................
                           00 01 07 05 81 13 02 00 08 06 30 00 00 02 00      ..........0....

        ---------------- Interface Descriptor -----------------
bLength                  : 0x09 (9 bytes)
bDescriptorType          : 0x04 (Interface Descriptor)
bInterfaceNumber         : 0x00
bAlternateSetting        : 0x00
bNumEndpoints            : 0x01 (1 Endpoint)
bInterfaceClass          : 0x09 (Hub)
bInterfaceSubClass       : 0x00
bInterfaceProtocol       : 0x00
iInterface               : 0x01 (String Descriptor 1)
 *!*ERROR  String descriptor not found
Data (HexDump)           : 09 04 00 00 01 09 00 00 01                        .........

        ----------------- Endpoint Descriptor -----------------
bLength                  : 0x07 (7 bytes)
bDescriptorType          : 0x05 (Endpoint Descriptor)
bEndpointAddress         : 0x81 (Direction=IN EndpointID=1)
bmAttributes             : 0x13 (TransferType=InterruptNotification)
wMaxPacketSize           : 0x0002
bInterval                : 0x08 (8 ms)
Data (HexDump)           : 07 05 81 13 02 00 08                              .......

        ------ SuperSpeed Endpoint Companion Descriptor -------
bLength                  : 0x06 (6 bytes)
bDescriptorType          : 0x30 (SuperSpeed Endpoint Companion Descriptor)
bMaxBurst                : 0x00 (up to 1 packets per burst)
bmAttributes             : 0x00
wBytesPerInterval        : 0x0002 (2 bytes)
Data (HexDump)           : 06 30 00 00 02 00                                 .0....

      ---------- Binary Object Store (FOREST) Descriptor -----------
bLength                  : 0x05 (5 bytes)
bDescriptorType          : 0x0F (Binary Object Store)
wTotalLength             : 0x002A (42 bytes)
bNumDeviceCaps           : 0x03
Data (HexDump)           : 05 0F 2A 00 03                                    ..*..

        ------------- USB 2.0 Extension Descriptor ------------
bLength                  : 0x07 (7 bytes)
bDescriptorType          : 0x10 (Device Capability Descriptor)
bDevCapabilityType       : 0x02 (USB 2.0 Extension)
bmAttributes             : 0x06
 LPMCapable              : 1 (Link Power Management protocol is supported)
 BESLAndAlternateHIRD    : 1 (BESL & Alternate HIRD definitions are supported)
 BaselineBESLValid       : 0 (not valid)
 DeepBESLValid           : 0 (not valid)
 BaselineBESL            : 0
 DeepBESL                : 0
Data (HexDump)           : 07 10 02 06 00 00 00                              .......

        ----- SuperSpeed USB Device Capability Descriptor -----
bLength                  : 0x0A (10 bytes)
bDescriptorType          : 0x10 (Device Capability Descriptor)
bDevCapabilityType       : 0x03 (SuperSpeed USB Device Capability)
bmAttributes             : 0x00
 Bit 0 Reserved          : 0x00
 Bit 1 LTM Capable       : 0x00 (on the)
 Bit 7:2 Reserved        : 0x00
wSpeedsSupported         : 0x0E (Full-Speed, High-Speed, SuperSpeed)
bFunctionalitySupport    : 0x01 (lowest speed with all the functionality is 'Full-Speed')
bU1DevExitLat            : 0x08   (less than 8 ĩS)
wU2DevExitLat            : 0x00BE (less than 190 ĩS)
Data (HexDump)           : 0A 10 03 00 0It 00 01 08 BE 00                     ..........

        --------- Container ID Capability Descriptor ----------
bLength                  : 0x14 (20 bytes)
bDescriptorType          : 0x10 (Container ID Capability)
bDevCapabilityType       : 0x04
bReserved                : 0x00
Container ID (UUID)      : 9F4B56F0-1DF6-11E0-AC64-0800200C9A66
Data (HexDump)           : 14 10 04 00 F0 56 4B 9F F6 1D E0 11 AC 64 08 00   .....VK ...... d..
                           20 0C 9A 66                                        ..f

      -------------------- String Descriptors -------------------
none


    =========================== USB Port2 ===========================

Connection Status        : 0x01 (Device is connected)
Port Chain               : 2-3-2-3-2
Properties               : 0x01
 IsUserConnectable       : yes
 PortIsDebugCapable      : no
 PortHasMultiCompanions  : no
 PortConnectorIsTypeC    : no
ConnectionIndex          : 2
CompanionIndex           : 0
 CompanionHubSymLnk      : USB#VID_2109&PID_0813#7&2f9c6413&0&3#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
 CompanionPortNumber     : 2

      ========================== USB Hub =========================

        ------------------- USB Hub Descriptor -----------------
bDescriptorLength        : 0x09 (9 bytes)
bDescriptorType          : 0x29 (Hub Descriptor)
bNumberOfPorts           : 0x04 (4 Ports)
wHubCharacteristics      : 0x00E0
 Power switching         : Ganged
 Compound device         : No
 Over-current protection : Global
 TT Think Time           : At most 32 FS bit times
 Port Indicators         : Supported
bPowerOnToPowerGood      : 0x32 (100 ms)
bHubControlCurrent       : 0x64 (100 mA)
DeviceRemovable          : 0x00
 Bit 0                   : 0 (reserved, any value)
 Bit 1                   : 0 (Device at Port 1 is removable)
 Bit 2                   : 0 (Device at Port 2 is removable)
 Bit 3                   : 0 (Device at Port 3 is removable)
 Bit 4                   : 0 (Device at Port 4 is removable)
 Bit 5                   : 0 (unused, must be 0)
 Bit 6                   : 0 (unused, must be 0)
 Bit 7                   : 0 (unused, must be 0)
PowerControlMask         : 0xFF
Data (HexDump)           : 09 29 04 E0 00 32 64 00 FF                        .)...2d..
HubIsBusPowered          : 0x00 (Self Powered)

        -------------- Extended USB Hub Descriptor -------------
HubType                  : USB 2.0 Hub
HighestPortNumber        : 4

        ------------------- USB Hub Descriptor -----------------
bDescriptorLength        : 0x09 (9 bytes)
bDescriptorType          : 0x29 (Hub Descriptor)
bNumberOfPorts           : 0x04 (4 Ports)
wHubCharacteristics      : 0x00E0
 Power switching         : Ganged
 Compound device         : No
 Over-current protection : Global
 TT Think Time           : At most 32 FS bit times
 Port Indicators         : Supported
bPowerOnToPowerGood      : 0x32 (100 ms)
bHubControlCurrent       : 0x64 (100 mA)
DeviceRemovable          : 0x00
 Bit 0                   : 0 (reserved, any value)
 Bit 1                   : 0 (Device at Port 1 is removable)
 Bit 2                   : 0 (Device at Port 2 is removable)
 Bit 3                   : 0 (Device at Port 3 is removable)
 Bit 4                   : 0 (Device at Port 4 is removable)
 Bit 5                   : 0 (unused, must be 0)
 Bit 6                   : 0 (unused, must be 0)
 Bit 7                   : 0 (unused, must be 0)
PowerControlMask         : 0xFF
Data (HexDump)           : 09 29 04 E0 00 32 64 00 FF                        .)...2d..

        ----------------- USB Hub Capabilities ----------------
HighSpeedCapable         : Yes
HighSpeed                : Yes
MultiTtCapable           : No
HubIsMultiTt             : No
ArmedWakeOnConnect       : No
IsBusPowered             : No
IsRoot                   : No
Data (HexDump)           : 03 00 00 00                                       ....

        +++++++++++++++++ Device Information ++++++++++++++++++
Device Description       : Generic USB Hub
Device Path              : \\?\usb#vid_05e3&pid_0610#8&34e76f17&0&2#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
Device ID                : USB  VID_05E3&PID_06108&34E76F17&0&2
Hardware IDs             : USB  VID_05E3&PID_0610&REV_0654 USBVID_05E3&PID_0610
Driver KeyName           : {36fc9e60-c465-11cf-8056-444553540000}\0042 (GUID_DEVCLASS_USB)
Driver                   : \SystemRootSystem32driversUsbHub3.sys (Version: 10.0.18362.1  Date: 2019-03-19)
Driver Inf               : C:\WINDOWS\inf\usbhub3.inf
Legacy BusType           : PNPBus
Class                    : USB
Class GUID               : {36fc9e60-c465-11cf-8056-444553540000} (GUID_DEVCLASS_USB)
Interface GUID           : {f18a0e88-c30c-11d0-8815-00a0c906bed8} (GUID_DEVINTERFACE_USB_HUB)
Service                  : USBHUB3
Enumerator               : USB
Location Info            : Port_#0002.Hub_#0017
Location IDs             : PCIROOT(0)#PCI(1400)#USBROOT(0)#USB(3)#USB(2)#USB(3)#USB(2), ACPI(_SB_)#ACPI(PCI0)#ACPI(XHC_)#ACPI(RHUB)#ACPI(HS03)#USB(2)#USB(3)#USB(2)
Container ID             : {9f4b56f0-1df6-11e0-ac64-0800200c9a66}
Manufacturer Info        : (Standard USB HUBs)
Capabilities             : 0x84 (Removable, SurpriseRemovalOK)
Status                   : 0x0180600A (DN_DRIVER_LOADED, DN_STARTED, DN_DISABLEABLE, DN_REMOVABLE, DN_NT_ENUMERATOR, DN_NT_DRIVER)
Problem Code             : 0
Address                  : 2
HcDisableSelectiveSuspend: 0
EnableSelectiveSuspend   : 0
SelectiveSuspendEnabled  : 0
EnhancedPowerMgmtEnabled : 0
IdleInWorkingState       : 1
WakeFromSleepState       : 0
Power State              : D0 (supported: D0, D1, D2, D3, wake from D0, wake from D1, wake from D2)

        +++++++++++++++++ Registry USB Flags +++++++++++++++++
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\usbflags\05E306100654
 osvc                    : REG_BINARY 00 00
 NewInterfaceUsage       : REG_DWORD 00000000 (0)

        ---------------- Connection Information ---------------
Connection Index         : 0x02 (2)
Connection Status        : 0x01 (DeviceConnected)
Current Config Value     : 0x01
Device Address           : 0x1A (26)
Is Hub                   : 0x01 (yes)
Device Bus Speed         : 0x02 (High-Speed)
Number Of Open Pipes     : 0x01 (1 pipe to data endpoints)
Pipe[0]                  : EndpointID=1  Direction=IN   ScheduleOffset=0  Type=Interrupt
Data (HexDump)           : 02 00 00 00 12 01 10 02 09 00 01 40 E3 05 10 06   [email protected]
                           54 06 01 02 00 01 01 02 01 1A 00 01 00 00 00 01   T...............
                           00 00 00 07 05 81 03 01 00 0C 00 00 00 00         ..............

        --------------- Connection Information V2 -------------
Connection Index         : 0x02 (2)
Length                   : 0x10 (16 bytes)
SupportedUsbProtocols    : 0x03
 Usb110                  : 1 (yes)
 Usb200                  : 1 (yes)
 Usb300                  : 0 (on the)
 ReservedMBZ             : 0x00
Flags                    : 0x02
 DevIsOpAtSsOrHigher     : 0 (Is not operating at SuperSpeed or higher)
 DevIsSsCapOrHigher      : 1 (Is SuperSpeed capable or higher)
 DevIsOpAtSsPlusOrHigher : 0 (Is not operating at SuperSpeedPlus or higher)
 DevIsSsPlusCapOrHigher  : 0 (Is not SuperSpeedPlus capable or higher)
 ReservedMBZ             : 0x00
Data (HexDump)           : 02 00 00 00 10 00 00 00 03 00 00 00 02 00 00 00   ................

    ---------------------- Device Descriptor ----------------------
bLength                  : 0x12 (18 bytes)
bDescriptorType          : 0x01 (Device Descriptor)
bcdUSB                   : 0x210 (USB Version 2.10)
bDeviceClass             : 0x09 (Hub)
bDeviceSubClass          : 0x00
bDeviceProtocol          : 0x01 (Hi-speed hub with single TT)
bMaxPacketSize0          : 0x40 (64 bytes)
idVendor                 : 0x05E3 (Genesys Logic, Inc.)
idProduct                : 0x0610
bcdDevice                : 0x0654
iManufacturer            : 0x01 (String Descriptor 1)
 *!*ERROR  String descriptor not found
iProduct                 : 0x02 (String Descriptor 2)
 *!*ERROR  String descriptor not found
iSerialNumber            : 0x00 (No String Descriptor)
bNumConfigurations       : 0x01 (1 Configuration)
Data (HexDump)           : 12 01 10 02 09 00 01 40 E3 05 10 06 54 06 01 02   [email protected]
                           00 01                                             ..

    ------------------ Configuration Descriptor -------------------
bLength                  : 0x09 (9 bytes)
bDescriptorType          : 0x02 (Configuration Descriptor)
wTotalLength             : 0x0019 (25 bytes)
bNumInterfaces           : 0x01 (1 Interface)
bConfigurationValue      : 0x01 (Configuration 1)
iConfiguration           : 0x00 (No String Descriptor)
bmAttributes             : 0xE0
 D7: Reserved, set 1     : 0x01
 D6: Self Powered        : 0x01 (yes)
 D5: Remote Wakeup       : 0x01 (yes)
 D4..0: Reserved, set 0  : 0x00
MaxPower                 : 0x32 (100 mA)
Data (HexDump)           : 09 02 19 00 01 01 00 E0 32 09 04 00 00 01 09 00   ........2.......
                           00 00 07 05 81 03 01 00 0C                        .........

        ---------------- Interface Descriptor -----------------
bLength                  : 0x09 (9 bytes)
bDescriptorType          : 0x04 (Interface Descriptor)
bInterfaceNumber         : 0x00
bAlternateSetting        : 0x00
bNumEndpoints            : 0x01 (1 Endpoint)
bInterfaceClass          : 0x09 (Hub)
bInterfaceSubClass       : 0x00
bInterfaceProtocol       : 0x00
iInterface               : 0x00 (No String Descriptor)
Data (HexDump)           : 09 04 00 00 01 09 00 00 00                        .........

        ----------------- Endpoint Descriptor -----------------
bLength                  : 0x07 (7 bytes)
bDescriptorType          : 0x05 (Endpoint Descriptor)
bEndpointAddress         : 0x81 (Direction=IN EndpointID=1)
bmAttributes             : 0x03 (TransferType=Interrupt)
wMaxPacketSize           : 0x0001
 Bits 15..13             : 0x00 (reserved, must be zero)
 Bits 12..11             : 0x00 (0 additional transactions per microframe -> allows 1..1024 bytes per packet)
 Bits 10..0              : 0x01 (1 byte per packet)
interval                : 0x0C (12 ms)
Data (HexDump)           : 07 05 81 03 01 00 0C                              .......

    ----------------- Device Qualifier Descriptor -----------------
Error                    : ERROR_GEN_FAILURE

      ---------- Binary Object Store (FOREST) Descriptor -----------
bLength                  : 0x05 (5 bytes)
bDescriptorType          : 0x0F (Binary Object Store)
wTotalLength             : 0x002A (42 bytes)
bNumDeviceCaps           : 0x03
Data (HexDump)           : 05 0F 2A 00 03                                    ..*..

        ------------- USB 2.0 Extension Descriptor ------------
bLength                  : 0x07 (7 bytes)
bDescriptorType          : 0x10 (Device Capability Descriptor)
bDevCapabilityType       : 0x02 (USB 2.0 Extension)
bmAttributes             : 0x06
 LPMCapable              : 1 (Link Power Management protocol is supported)
 BESLAndAlternateHIRD    : 1 (BESL & Alternate HIRD definitions are supported)
 BaselineBESLValid       : 0 (not valid)
 DeepBESLValid           : 0 (not valid)
 BaselineBESL            : 0
 DeepBESL                : 0
Data (HexDump)           : 07 10 02 06 00 00 00                              .......

        ----- SuperSpeed USB Device Capability Descriptor -----
bLength                  : 0x0A (10 bytes)
bDescriptorType          : 0x10 (Device Capability Descriptor)
bDevCapabilityType       : 0x03 (SuperSpeed USB Device Capability)
bmAttributes             : 0x00
 Bit 0 Reserved          : 0x00
 Bit 1 LTM Capable       : 0x00 (on the)
 Bit 7:2 Reserved        : 0x00
wSpeedsSupported         : 0x0E (Full-Speed, High-Speed, SuperSpeed)
bFunctionalitySupport    : 0x01 (lowest speed with all the functionality is 'Full-Speed')
bU1DevExitLat            : 0x08   (less than 8 ĩS)
wU2DevExitLat            : 0x00BE (less than 190 ĩS)
Data (HexDump)           : 0A 10 03 00 0It 00 01 08 BE 00                     ..........

        --------- Container ID Capability Descriptor ----------
bLength                  : 0x14 (20 bytes)
bDescriptorType          : 0x10 (Container ID Capability)
bDevCapabilityType       : 0x04
bReserved                : 0x00
Container ID (UUID)      : 9F4B56F0-1DF6-11E0-AC64-0800200C9A66
Data (HexDump)           : 14 10 04 00 F0 56 4B 9F F6 1D E0 11 AC 64 08 00   .....VK ...... d..
                           20 0C 9A 66                                        ..f

      -------------------- String Descriptors -------------------
none

Tracing

These are the package tracking information obtained from the AliExpress system:

2020.03.31 17:20 (GMT-7): Delivery successful
2020.03.28 10:38 (GMT-7): Cleared customs
2020.03.23 08:31 (GMT-7): Accepted by Last Mile Carrier
2020.03.17 16:28 (GMT-7): Departed country of origin
2020.03.12 15:01 (GMT-7): Shipment accepted by airline
2020.03.12 04:47 (GMT-7): Shipment left country of origin warehouse
2020.03.12 00:16 (GMT-7): Shipment at country of origin warehouse
2020.03.11 23:46 (GMT-7): Shipment dispatched

And these are the information obtained on the site of the station:

31/03/2020
17:19
[REMOVED] / SP Object delivered to the recipient
31/03/2020
14:02
[REMOVED] / SP object out for delivery to the recipient
30/03/2020
08:32
INDAIATUBA / SP
Objeto encaminhado
de Unidade de Tratamento em INDAIATUBA / SP for distribution Unit in [REMOVED] / SP
28/03/2020
10:55
CURITIBA / PR
Objeto encaminhado
de Unidade de Distribuição em CURITIBA / PR for Treatment Unit in INDAIATUBA / SP
28/03/2020
10:53
CURITIBA / PR finalized Customs supervision
23/03/2020
08:53
CURITIBA / PR	Objeto recebido pelos Correios do Brasil

Informar nº do documento para a fiscalização e entrega do seu objeto. Click here My Imports
13/03/2020
10:32
SWEDEN /
Objeto encaminhado
de País em SUECIA / countries in International treatment unit / BR

Informar nº do documento para a fiscalização e entrega do seu objeto. Click here My Imports
13/03/2020
10:29
SWEDEN / 	Objeto recebido na unidade de exportação no país de origem

Informar nº do documento para a fiscalização e entrega do seu objeto. Click here My Imports
13/03/2020
10:24
SWEDEN / 	Objeto postado

Informar nº do documento para a fiscalização e entrega do seu objeto. Click here My Imports

Table-Summary

This is the table-summary of purchase:

Product Name: Hub USB 3.0 Orico WH4P1 com 4 doors and entrance to source
Name Original: ORICO High Speed 4 Ports USB 3.0 HUB With Power Supply Port USB2.0 Splitter OTG Adapter for iMac Laptop Desktop Accessories
Store: AliExpress | Store: Orico Official Store
Value: R$ 34,08
Current value: R$ 48,97
Payment Method: Credit Card Visa International
Shipping Type: Aliexpress Standard Shipping
Shipping Fee: R$ 16,62
Package Home Country: China
Purchase Data: 08/03/2020
Submission Date: 11/03/2020
Data Delivery: 31/03/2020
Time in Transit: 20 days
Declared content: usb hub
Type Marked Content: Others
Declared Value: USD $0.9
Taxed: Not
Taxable Value: -
Tax Value: -

Final Considerations

The Hub USB 3.0 Orico WH4P1 worked correctly and really presents itself as a USB Hub 3.0, ensuring the highest bandwidth of the standard. É compacto e leve para ser levado na mochila e estar sempre disponível quando necessário.

Share this article with your friends if you liked 😉 . If you also want to shop in AliExpress, directly from Hong Kong, click here and good shopping.

0 0 votes
Article Rating

Skooter

Skooter is a computer scientist and the founder of Skooter Blog. He is interested in everything related to technology and he likes to save money by making his purchases directly from abroad.

Permanent link to this article: https://www.skooterblog.com/2020/04/02/review-hub-usb-3-0-orico-wh4p1-com-4-portas-e-entrada-para-fonte-aliexpress/

Sign up
Notify about
guest
3 Comments
older
more new top rated
Inline Feedbacks
See all reviews

Parece ser um ótimo hub, comprei ele no começo do mês passado, também na loja oficial da marca no Aliexpress. Também preferi a versão com cabo de 30cm pra não ficar emaranhado de fio na mesa. I paid 30,89 nele com esse mesmo frete (Aliexpress Standard Shipping) usando cupom de $3 para novas contas, mas com dólar alto do jeito que está, sairia muito mais caro hoje.

Agora eu tô espantado com a rapidez com que você recebeu a encomenda, ainda mais nessa pandemia, pois eu comprei no dia 04/03, o vendedor somente postou no dia 10/03, mas segundo o rastreamento, ele nem chegou no Brasil ainda 😦 Talvez pelo seu seu ter sido enviado da Suécia, it's mine, da China.

0
Reply
Skooter

Também estranhei. Also because I have other older packages still pending.

0
Reply

Yeah, hope mine doesn't take too long, because it’s complicated to use a laptop with just 3 USB outputs. I like to play lying in bed, then only the wireless mouse, control receiver and USB DAC for headphone already occupy all ports. Anyway, thanks for the analysis.

0
Reply
3
0
We would like to know what you think, Leave your commentx
()
x